A custom notebook order can take months of planning, and one short step decides how it turns out: notebook sample approval. When you sign off a sample, you tell the factory “make thousands exactly like this”. Anything you miss at that moment is repeated across the whole order.
Most problems buyers discover on delivery were already visible on the sample. A logo sat two millimetres too low. The paper let gel ink show through. The spiral caught when pages turned. Nobody tested for it, so nobody saw it. This guide gives you a practical checklist for reviewing a notebook sample, simple tests you can do at your desk, and a clear way to record your decision. It is based on the sampling steps Lalumi uses for custom notebooks and journals.
What Is Notebook Sample Approval?
Notebook sample approval is the formal step where a buyer inspects a physical sample and confirms, in writing, that it meets the agreed specification. From that point the approved sample becomes the reference for production and for quality control.
It matters for three reasons:
- It fixes the standard. Photos and descriptions leave room for interpretation. A signed sample does not.
- It protects both sides. If the bulk order differs from the sample, you have a clear basis for discussion.
- It controls cost. A correction at sample stage costs little. The same correction after printing can mean remaking the order.
Prototype Sample vs Pre-Production Sample
Buyers usually see two kinds of sample, and they serve different purposes.
| Prototype | Échantillon de présérie | |
|---|---|---|
| When it is made | Before you place the order | After the order is placed, before mass production |
| But | Check design, materials and construction | Final confirmation of what will be produced |
| Changes expected | Yes, revisions are normal | Only corrections to match the approved prototype |
| Cost | A sample fee usually applies | Normally part of the order process |
| What to do with it | Review, request changes, approve | Compare with the approved prototype and confirm |
Lalumi follows this two-stage approach. A prototype sample is made first, for which a fee applies, and it is revised until you approve it. A pre-production sample follows once the order is placed. The full sequence is set out on our OEM and ODM service page.
Before the Sample Arrives: Get Ready
A sample can only be judged against something. Before it arrives, put together:
- Your written specification. Size, page count, paper weight and shade, ruling, binding, cover material, logo method, extras and packaging.
- Colour references. A Pantone number or a physical swatch for each brand colour.
- Your artwork files. The final versions you sent to the factory.
- Basic tools. A steel ruler, a small scale, and the pens your customers are most likely to use.
- Good light. Check colours in daylight or under neutral white light, not under warm office lamps.
If you have not finalised the specification, our guide to custom notebook cost explains each element and how it affects price.

The Notebook Sample Approval Checklist
Work through the sample in the same order every time. These seven areas cover almost everything that goes wrong.
1. Size and construction
Measure the closed notebook, the cover and an inner page. Standard formats such as A5 and B5 are defined in ISO 216, but many notebooks use their own dimensions. Several Lalumi hardcover and soft cover models, for example, are listed at 205 mm x 143 mm. Check the sample against the size in your specification, and agree with the manufacturer what tolerance is acceptable.
- Closed size, thickness and weight
- Cover overhang on a hardcover is even on all three sides
- Corners are square or evenly rounded
- The notebook closes flat and does not spring open
2. Cover
The cover carries your brand, so give it the most attention.
- Material and texture match what you chose
- Colour matches your reference in neutral light
- Logo is in the right position, at the right size, and straight
- Foil is complete, with no gaps or rough edges
- Debossing is even in depth
- Lamination has no bubbles, scratches or lifting at the edges
- The surface resists a firm rub with a thumb
Measure the logo position from two edges and write the numbers down. “Looks about right” is how a logo ends up off-centre on 3,000 covers.
3. Paper
Paper is what your customer feels on every page. Check the weight, the shade and the ruling. Paper weight is expressed in grams per square metre, and the test method is defined in ISO 536. You do not need a laboratory to notice paper that feels thinner than you ordered, but you can ask the manufacturer to confirm the grammage. Our notebook paper GSM guide explains what each weight is suited to.
- Paper shade: white, natural white or ivory, as specified
- Ruling type, line spacing and line colour
- Margins are equal and lines run parallel to the page edge
- Page count matches the specification
- No dirty marks, creases or uneven trimming
4. Binding
Binding failures cause returns, so test it harder than you think you need to. What to look for depends on the type.
| Binding | What to check |
|---|---|
| Sewn or case-bound | Opens flat without cracking the spine; no loose threads; first and last pages are firmly attached |
| Spiral or wire | Pages turn freely through 360 degrees; wire ends are closed; holes are evenly punched and not torn |
| Soft cover | Spine does not crease or split after repeated opening; cover returns to flat |
| Refillable | Inserts slide in and out easily; elastic or rings hold them securely |
If you are still choosing between types, see our comparison of notebook binding types.
5. Printing and inner pages
- Printed text is sharp and correctly spelled, including the small print
- Colours on printed covers and inserts match your reference
- Front and back printing line up on the page
- Custom inner pages, such as planners or title pages, are in the right order
6. Extras
- Ribbon marker is the right colour and length, and its end is sealed
- Elastic closure is firm but not so tight that it bends the cover
- Back pocket is glued on three sides and opens properly
- Pen loop fits the pen you plan to sell with it
7. Packaging and labelling
- Belly band, sleeve or box fits without forcing
- Barcode scans with a phone or scanner
- Label text, product name and country of origin are correct
- Each notebook is protected from scuffing in transit
Simple Tests You Can Do at Your Desk
None of these needs special equipment, and together they take about fifteen minutes.
| Test | How to do it | What you want to see |
|---|---|---|
| Bleed-through | Write a few lines with a ballpoint, a gel pen, a fountain pen and a highlighter | Ink does not show clearly on the reverse side |
| Smudge | Run a finger across gel ink after a few seconds | Ink is dry and does not smear |
| Lay-flat | Open the notebook in the middle and let go | Pages stay open, or nearly so, without holding |
| Page pull | Pull one page firmly near the spine on a spare sample | The page does not come away |
| Open and close | Open the cover fully fifty times | No cracking at the hinge or spine |
| Rub | Rub the logo and cover with a dry cloth | Foil and print stay intact |
| Elastic | Stretch and release the elastic twenty times | It returns to its length and stays attached |
Run destructive tests on a spare copy, never on the sample you plan to sign.

Common Sample Problems and How to Report Them
Clear feedback gets a corrected sample faster. For each issue, send a photo, a measurement where it applies, and the result you want.
| Problem | Unclear feedback | Useful feedback |
|---|---|---|
| Logo position | “Logo looks wrong” | “Logo is 18 mm from the top edge. It should be 22 mm, centred” |
| Cover colour | “Colour is off” | “Cover is lighter than Pantone 19-4052. Please match the swatch we sent” |
| Paper | “Paper feels cheap” | “Ink shows through with a gel pen. Please quote 100 gsm in place of 80 gsm” |
| Binding | “Binding is weak” | “Three pages came loose near the back cover after opening flat” |
| Elastic | “Elastic is bad” | “Elastic is too tight and bends the cover. Please lengthen by 5 mm” |
Put all comments in one message, numbered, so nothing is lost between rounds.
How to Record Notebook Sample Approval
Approval should never be a quick “looks good” in a chat message. Do it properly:
- Approve in writing. State the sample reference, the date and that it is approved for production.
- Sign and date the sample. Keep one signed copy and return or reference the other.
- List any accepted deviations. If you accept the sample with one small change, describe that change exactly.
- Attach the final specification. The sample and the written spec should say the same thing.
- Store the sample safely. Keep it flat, dry and out of sunlight, so colours do not change before the goods arrive.
Remember what approval commits you to. Once you approve, the manufacturer buys materials and prepares tooling to match that sample. Later changes usually cost money and time.
What Happens After Approval
After the prototype is approved and the order is placed, a pre-production sample confirms the final result, and mass production begins. Lalumi gives a typical production time of 40–45 days after sample approval, which varies with quantity and season. Details are confirmed against the approved sample, and quality is checked during and after production, before the goods are packed and shipped.
Larger buyers often add a final inspection based on sampling plans such as ISO 2859-1, which sets out how many pieces to check from a batch. Whatever method you use, the approved sample is the standard the inspector works from.
What Buyers Should Check Before Purchasing
Sample approval goes more smoothly when the buying decision behind it is sound. Before you commit to a supplier, check these points:
- The quotation lists every specification, so the sample can be compared with it
- Sample cost, sample lead time and the number of revision rounds are stated
- The minimum order quantity fits your plan. Lalumi product pages list, for example, 3,000 pieces for several hardcover and soft cover notebooks and 5,000 pieces for an A5 spiral notebook
- The supplier explains how defects found after delivery are handled
- Production time is counted from sample approval, and you know the factory holiday dates
- Packaging and labelling requirements are included from the start
What affects quality and price
The same choices drive both. Cover material, paper weight, page count, binding, decoration such as foil and embossing, and packaging all raise or lower the unit price and the risk of defects. A simple specification is easier to produce consistently. If budget is tight, reduce the number of decorative processes before you reduce the paper quality.
Sustainability: Fewer Sample Rounds, Less Waste
Every sample round uses materials and air freight. You can cut both without lowering your standard:
- Approve artwork and layout on screen before a physical sample is made
- Send complete feedback once, not in several partial messages
- Decide on paper and cover materials early, so samples are not remade for a change of mind
- Ask for documentation if you plan to make environmental claims about paper or packaging, and make only the claims you can support
Why Choose Lalumi for Custom Notebooks
Lalumi is an OEM and ODM stationery manufacturer based in Ningbo, China. We produce hardcover, soft cover, spiral, sewn-bound and refillable notebooks and journals for brands, retailers and wholesale buyers. You can see the main options on our custom notebook and journal manufacturer page.
- Samples before production. A prototype sample and a pre-production sample are built into the process.
- Revisions until you approve. The sample is adjusted until it matches your requirements.
- Published specifications. Product pages list size, materials and MOQ, such as the square-spine hardcover notebook, le soft cover notebook et le refillable PU leather notebook.
- Confidentiality. Your designs, logos and product plans are used only for your project.
Why Partner With Lalumi
Sampling is where a supplier relationship is tested. Lalumi supports wholesale and private label buyers from the first brief through feasibility review, quotation, prototype sample, revisions, pre-production sample, production with quality checks, and shipment.
One product team handles notebooks together with pens, pencil cases and gift sets, so a matching collection can be sampled and approved as a set. For repeat orders, the approved sample stays as the reference, which keeps each new batch consistent with the last. Browse the full collection de cahiers to see what can be customised.
Planning a notebook order? Contactez Lalumi with your specification or a reference photo. We reply to product enquiries and business partnership requests within 24 hours.
FAQs About Notebook Sample Approval
What is the difference between a prototype sample and a pre-production sample?
A prototype sample is the first physical version of your notebook. It is made to check the design, materials and construction, and it often goes through revisions. A pre-production sample is made after the order is placed, using the materials and methods planned for the bulk run. It is your final confirmation before mass production, so check it against the approved prototype point by point.
How many notebook samples should I request?
Ask for at least two identical samples of each design. Keep one as your reference and sign the other for the manufacturer, so both sides hold the same approved standard. If several people in your company must review the notebook, or you want to run destructive tests such as pulling pages, request extra copies at the start. It is cheaper than a second sample round.
What should I check first during notebook sample approval?
Start with the points that cannot be fixed cheaply later: size, cover material, binding type and paper. Then check the logo position and colour, the ruling, and extras such as the ribbon and elastic. Finish with packaging and barcodes. Working in that order during notebook sample approval means you catch structural problems before you spend time on small details.
Can I change the design after I approve the sample?
You can ask, but expect extra cost and time. Once a sample is approved, the manufacturer orders materials and prepares printing plates, foil dies and cutting tools based on it. A change after that point may mean new tooling and a new sample. If you are unsure about any detail, resolve it before notebook sample approval, not after.
What happens if the bulk order does not match the approved sample?
The approved sample is the reference for the order, so start by comparing the delivered goods with it and documenting the differences with photos and measurements. Then raise the issue with the manufacturer in writing. How defects are handled should be agreed before production, including what counts as a defect and whether goods are reworked or replaced.











